Has anyone had success with getting an XDS200 (USB) device to function on a Mac with a Windows-7 Parallels virtual machine? The XDS100 does not seem to have any problem, but testing a XDS200 from the CCS target configuration yields the message below. Note that I can rule out a problem with the emulator (or target) as the same setup works flawlessly on a native Windows machine. Thanks, Beat [Start] Execute the command:%ccs_base%/common/uscif/dbgjtag -f%boarddatafile% -rv -o -S integrity [Result] -----[Print the board config pathname(s)]------------------------------------ C: Users beat AppData Local.TI 693494126 0 0 BrdDat testBoard.dat -----[Print the reset-command software log-file]----------------------------- This utility has selected a 560/2xx-class product. This utility will load the program 'xds2xxu.out'.
E_RPCENV_IO_ERROR(-6) No connection Failed to open i/o connection (xds2xxu:0) An error occurred while soft opening the controller. -----[An error has occurred and this utility has aborted]-------------------- This error is generated by TI's USCIF driver or utilities. The value is '-250' (0xffffff06). The title is 'SC_ERR_ECOM_EMUNAME'. The explanation is: An attempt to access the named emulator via USCIF ECOM has failed. I don't have an environment that I can try this in so I can't help much. The XDS100 uses the OS driver for the FTDI usb interface chip while the xds200 uses stock drivers that ship with the OS.
Thus they are very different in the way the OS detects them. I know we have had issues on Ubuntu 13.04 and Fedora 18 where the OS gets confused and thinks it is a modem. Samsung pc suite download for macbook pro. We had to update or driver rules file to handle that. Maybe Mac OS has a similar issue? There is also a LAN version of the xds200 available.
• On board USB XDS100v2 JTAG emulator. HALCoGen GUI-based device configuration and driver examples. The several configurations of the TMS570LS31 series integrate an Ethernet MAC on chip. Please consult the family datasheets for availability. This interface is.
Hi, I got to this post because I have exactly the same problem. I have tested CCS (last version 5 and beta version 6) in a Windows 7 Pro x86 virtual machine running under VMWare Fusion (last version) and Parallels (last version) in a Macbook Pro (OSX last version). The emulator I used is the XDS200 from Blackhawk and Digital Spectrum. The same CCS/Windows setup worked flawlessly in a 'real' Windows 7 x86 machine.
Xds100v2 Driver For Mac Download
I asked for support in Parallel and they told me the problem should be in the 'OSX/emulator driver' relationship. I have another USB problem with other device that worked in a 'real' machine but have strange behaviour in a 'virtual' machine under VMWare and Parallels.
I found some recommendations regarding VMWare USB configurations to improve compatibility. One of these recommendations (VMWare USB quirks) allow me to reach one step further in the emulator communications but stops working as usual. Have you resolved this issue? In reply to: I have the same issue. Just got four XDS200 emulators. All of them fail to connect on MacBook with Parallels 9.0.24237.
I have been running XDS100 and other emulators on this combination before with CCS 4 and no issue. Using Windows 7. When I plug the emulator, it enumerates on the Mac as: • XDS2xx USB Emulator - Composit: • Product ID: 0xbef0 • Vendor ID: 0x0451 (Texas Instruments) • Version: 1.00 • Serial Number: S200-00 • Speed: Up to 480 Mb/sec • Manufacturer: Spectrum Digital • Location ID: 0x1a120000 / 4 • Current Available (mA): 500 • Current Required (mA): 500 The Windows machine then installs two drivers: • XDS2xx Emulator CDC Serial Port (COM10) • XDS2xx User CDC Serial Port (COM12) When I use a debug session on CCS v 6, it just hangs. If I run the Test Connection, I get: • [Start: Texas Instruments XDS2xx USB Emulator_0] • Execute the command: •%ccs_base%/common/uscif/dbgjtag -f%boarddatafile% -rv -o -S integrity • [Result] • -----[Print the board config pathname(s)]------------------------------------ • C: Users ADMINI~1 AppData Local TEXASI~1 CCS ti 0 0 BrdDat testBoard.dat • -----[Print the reset-command software log-file]----------------------------- • This utility has selected a 560/2xx-class product. • This utility will load the program 'xds2xxu.out'. Closing the window hangs CCS.
Disconnecting the emulator finishes the process with. In reply to: If I use BlackHawk USB560M and Spectrum Digital XDS560v2 STM with CCS 6, I am also unable to get them to work, but CCS does not hang. I get this error: • [Start: Blackhawk USB560-M Emulator_0 • Execute the command: •%ccs_base%/common/uscif/dbgjtag.exe -f%boarddatafile% -rv -o -F inform,logfile=yes -S pathlength -S integrity • [Result] • -----[Print the board config pathname(s)]------------------------------------ • C: Users ADMINI~1 AppData Local TEXASI~1 CCS ti 0 0 BrdDat testBoard.dat • -----[Print the reset-command software log-file]----------------------------- • This utility has selected a 560/2xx-class product. • This utility will load the program 'bh560usbm.out'. • The library build date was 'May 21 2014'.